Position the OrthoMark ball (represented by the blue disc) near the bone of interest in the manner shown. Ensure that the OrthoMark ball is within the image field and is the same distance from the digital detector (the same plane) as the bone. If possible, palpate the anatomy to help precisely align OrthoMark.
Use is not limited to positions shown here. These are shown only as an indication of use.
OM-1001
Acrylic Base Model OM-1001 is designed for use…well…anywhere you can place it. We’ve seen it draped over the top edge of an upright bucky and attached with Velcro to the upright stand itself. Your imagination is the limit. That being said, the original intent was to stand freely on the x-ray table, or to slide beneath the patients leg to hold it in place.
Position the sphere normally after positioning the base.
OM-1002
Magnetic Base Model OM-1002 is designed for use on ferrous surfaces.
Simply attach it to your surface, position the OrthoMark sphere, and you’re good to go.
With our new OM-1002SD “sticky disc” you can create a ferrous surface to attach your OM-1002 to almost anywhere. See it below.
OM-1003
Suction Cup Model OM-1003 is designed for use on smooth surfaces. This unit is not intended for use on dimpled or other surfaces.
When using, please be sure to place the suction cup firmly on the surface, then activate the lever handle by squeezing and “closing” the handles together. This will provide a firm hold and allow the OrthoMark ball to be positioned easily.
When finished, it’s a good idea to lightly clean the surface with water and place on a counter or in a cabinet to avoid dust gathering. It is also best not to leave the suction cup attached to a wall or your equipment. The suction will eventually dissipate and the unit will fall.
OM-1005
Clamp Base Model OM-1005 is designed for use on any clampable surface without sharp edges, flat or round, up to 2” thick. The band may break if overstretched repeatedly. If desired, the orange band may be pulled out to allow a slightly wider grip.
When using, squeeze the handles, let it grip your surface, and release. When attaching to a round surface, try to place the centerline of the clamp pads directly over the clamped surface.
Position the sphere normally afterward.
OM-1006
Shorty 2.5” Quick Suction Cup Model OM-1006 is designed for use on smooth surfaces, by fast techs.
When using, prepare OrthoMark for it’s destination by getting it as close to the desired height as possible. Then holding the base in one hand, the end of the arm in the other, and in one deft movement, plunge the suction cup downward and simultaneously finely position the sphere. This should offer about two to ten minutes worth of holding power.
When finished, it is a good idea to lightly clean the surface with water and place on a counter or in a cabinet to avoid dust gathering. It is also best not to leave the suction cup attached to a wall or your equipment. The suction will eventually dissipate and the unit will fall.
OM-1008
Strap Model OM-1008 is designed for use in any way your imagination can make it work.
When using, slip the strap around your patients body, buckle toward the front, release the latch and snug it up, then secure the latch. It does not need to be tight.
OM-1009
Lever Action 2.75” Super Suction Model OM-1009 is designed for use on any smooth surface and surfaces that are slightly dimpled or not completely smooth. This unit will not function well on a surface that appears “sandy” or rough.
When using, simply place against the surface and squeeze lever until it clicks. This will provide a firm hold and allow the OrthoMark ball to be positioned easily. Remove by pressing the lock button on the side.
***Ensure that the release button is pressed and the handle extends to the open position before pulling the suction cup away from the surface. Failure to do so may result in damage to the suction cup and is not covered under warranty.
When finished, it is a good idea to lightly clean the surface with water and place on a counter or in a cabinet to avoid dust gathering. It is also best not to leave the suction cup attached to a wall or your equipment. The suction will eventually dissipate and the unit will fall.
OM-1010
Super 2.9” Plunger Suction Cup Model OM-1010 is designed for use on any smooth surface and surfaces that are slightly dimpled or not completely smooth. This unit will not function well on a surface that appears “sandy” or rough.
When using, please be sure to activate the plunger until the red line disappears. This will provide a firm hold and allow the OrthoMark ball to be positioned easily. Remove by gripping the two rubber tabs and squeezing.
When finished, it is a good idea to lightly clean the surface with water and place on a counter or in a cabinet to avoid dust gathering. It is also best not to leave the suction cup attached to a wall or your equipment. The suction will eventually dissipate and the unit will fall.
OM-1011
The large clamp base Model OM-1011 is designed for use on any clampable surface, flat or round, up to 2.375” thick. It works especially well when attached to patient grab handles, or step stool and elevated stair handles.
When using, simply position and tighten. When attaching to a round surface, position the V notch on the fixed side of the clamp where you intend to clamp, use the speed tightening nut for coarse adjustment then the large wheel for additional clamping force. This is a strong clamp, so don’t overtighten.
Position the sphere normally afterward.
OM-1012
The small clamp base Model OM-1012 is designed for use on any clampable surface, flat or round, up to 2” thick, but works best on round surfaces with a maximum thickness of 1.5″. It works especially well when attached to patient grab handles, or step stool and elevated stair handles.
When using, simply position and tighten. When attaching to a round surface, position the V notch on the fixed side of the clamp where you intend to clamp, use the T-handle to tighten. This is a strong clamp, so don’t overtighten.
Position the sphere normally afterward.
OM-SD
The OM-SD “Sticky Disc” is designed to allow the magnetic base Model OM-1002 to be attached to almost any surface.
Simply clean and dry your surface, peel off the adhesive cover and attach it to your surface. Allow it to cure for 48 hours, then mount your OM-1002 to it.
The adhesive tape is very sticky and very difficult to remove, so position it thoughtfully and be careful not to drop it on any other surface.
It also works with the OM-1006 and OM-1009.